Soğuk Haddelenmiş Çelik Rulo: Kaliteler, Kalınlıklar ve Rulo İç Çapı

Luyuan Steel Technical Team | Steel Manufacturing & Export | Updated September 2026

Cold rolled steel coil from Luyuan is supplied at 0.12–5.0 mm thickness, with coil inner diameters of 508 mm or 610 mm, most commonly as SPCC, SPCD or SPCE depending on how much drawing or forming the part requires.

Soğuk Haddelenmiş Çelik Rulo: Kaliteler, Kalınlıklar ve Rulo İç Çapı

Thickness Range: What’s Published

CR Coil covers a wider thickness band than CR Levha, which is why coil form is the default for anything requiring roll-forming, slitting, or decoiling equipment rather than a flat, pre-cut piece.

SPCC, SPCD and SPCE: Matching Grade to Forming Operation

Luyuan’s manufacturing application pages reference SPCC, SPCD, and SPCE — three grades under JIS G3141, Japan’s standard for cold-reduced carbon steel sheet and strip, maintained under the Japanese Industrial Standards Committee (JISC) system. The three aren’t interchangeable tiers of the same product; they’re differentiated by carbon content, which controls how much the material can be drawn or stretched before it cracks.

Specifying SPCC for a part that actually needs SPCE-level formability is one of the more common ordering mistakes on a stamping order — the coil will roll off the line, but cracking or splitting shows up downstream at the press, after the material has already been cut and tooled. Matching grade to the part’s draw depth before the order is placed avoids that scrap.

3 Steps to Confirm the Right Grade Before Ordering

1. Check the deepest draw or bend radius on the part, not just the flat blank dimensions — that’s what actually determines whether SPCC, SPCD, or SPCE is needed.
2. Confirm thickness against the 0.12–5.0 mm coil range(or 0.20–0.50 mm if cut sheet is required instead of coil).
3. Specify coil ID as 508 mm or 610 mmto match the uncoiler or decoiling equipment on the receiving line — this is a common miss on cross-border orders where the buyer’s line equipment wasn’t specified up front.

Why Coil Inner Diameter Isn’t a Minor Detail

A 508 mm ID coil and a 610 mm ID coil aren’t interchangeable on most decoiling equipment — the mandrel or uncoiler on the receiving line is typically built for one or the other, not both. An order placed without specifying coil ID often defaults to whichever is standard for the mill, which may not match the buyer’s equipment. Confirming ID alongside thickness and grade avoids a coil arriving at the dock that the receiving line can’t physically load.

Soğuk Haddelenmiş Çelik Rulo: Kaliteler, Kalınlıklar ve Rulo İç Çapı

Annealing and Surface Options

Cold rolling work-hardens the steel, so most CR coil goes through an annealing step afterward to restore ductility before it’s shipped for forming. Luyuan’s processing options for cold rolled products include cutting, bending, punching, annealing, black annealing, welding, and decoiling, depending on the specific product and order. Black annealing — annealing without a fully oxygen-free atmosphere — leaves a different surface appearance than bright annealing, which matters for parts where surface finish is visible in the final application rather than hidden under paint or coating.

Certification and Documentation to Request

No SKU-specific certificate number is publicly disclosed for CR Coil. What is documented and available at the company level: a full English Mill Test Certificate with each shipment, 100% pre-shipment inspection, batch traceability from furnace number through shipment, and chemical composition and mechanical property testing. SGS, Bureau Veritas, Intertek, or a buyer-appointed inspector can be arranged for third-party verification — worth confirming in advance if the part is going into an automotive or appliance supply chain with its own incoming-inspection requirements.

Where Cold Rolled Coil Loses to Hot Rolled

Cold rolled coil isn’t the right call for every job. It costs more per ton than hot rolled material for the same base chemistry, because cold rolling and annealing are additional process steps on top of hot rolling. It also doesn’t extend as far into heavier gauges — Luyuan’s sıcak haddelenmiş rulo range runs up to 4.0 mm, while cold rolled coil’s advantage is really in the thinner end of that range, where surface finish and dimensional tolerance matter more than raw section thickness. For thick structural components where surface finish is irrelevant, hot rolled is the more economical choice; for stamped, drawn, or visible sheet-metal parts, cold rolled’s tighter tolerance and cleaner surface are usually worth the premium.

Soğuk Haddelenmiş Çelik Rulo: Kaliteler, Kalınlıklar ve Rulo İç Çapı

FAQ

Q: What’s the difference between SPCC, SPCD and SPCE?

C: Üçü de JIS G3141 soğuk haddelenmiş karbon çeliği kalitesidir. SPCC bükme ve sığ çekme için ticari kalite, SPCD orta derinlikte derin çekme için çekme kalitesi, SPCE ise en zorlu şekillendirme işlemleri için en düşük karbon içeriğine sahip derin çekme kalitesidir.

S: Hangi rulo iç çapları mevcut?

A: 508 mm and 610 mm. Confirm which one matches your decoiling equipment before ordering — the two aren’t interchangeable on most uncoilers.

S: Soğuk haddelenmiş rulo hangi kalınlık aralığını kapsar?

C: Rulo halinde 0,12–5,0 mm. Kesilmiş sac ayrıca 0,20–0,50 mm olarak mevcuttur.

S: Soğuk haddelenmiş rulo neden tavlama gerektirir?

C: Soğuk haddeleme çeliği pekleştirir ve sünekliği azaltır. Tavlama, malzeme preste veya rulo şekillendirmeye girmeden önce şekillendirilebilirliği geri kazandırır. Siyah tavlama ve parlak tavlama farklı yüzey görünümleri üretir.

S: Soğuk haddelenmiş rulo nasıl fiyatlandırılır?

C: Referans fiyat metrik ton başına yaklaşık 585–635 USD'dir; nihai fiyat ise kaliteye, kalınlığa, rulo iç çapına, tavlamaya ve sipariş hacmine bağlıdır.