Лист из нержавеющей стали ASTM A240 304: характеристики и применение

Luyuan Steel Technical Team | Technical Content & Export Specification Support | Published: 23 August 2026

ASTM A240 covers stainless plate, sheet and strip for pressure vessels and general applications. Type 304 (UNS S30400) requires minimum 515 MPa tensile, 205 MPa yield and 40% elongation. For ASME Code vessels, order to ASME SA-240 rather than A240, and confirm the edition on the certificate.

What A240 actually covers, and what it leaves to another standard

What A240 does not do is set dimensional tolerance, flatness, edge condition or surface finish designation. Those sit in ASTM A480/A480M, the general requirements specification for flat-rolled stainless. In practice this means a purchase order reading only “ASTM A240 304, 3 mm” has specified the metallurgy and left the thickness tolerance, flatness and finish unspecified. Most disputes over stainless sheet deliveries are A480 disputes, not A240 disputes.

There is a third document buyers encounter and misuse. ASTM A959 is a guide for harmonised standard grade compositions for wrought нержавеющие стали. It is a composition reference, not a product specification, so “A959 304 plate” is not something a mill produces to. If a petrochemical enquiry arrives written that way, the material specification you actually need is A240 (or SA-240), with A959 relevant only as a cross-reference to the equivalent grade designation in another national system.

Type 304 chemistry under A240

Element	Limit (% by mass)
Carbon (C)	0.07 max
Manganese (Mn)	2.00 max
Phosphorus (P)	0.045 max
Sulphur (S)	0.030 max
Silicon (Si)	0.75 max
Chromium (Cr)	17.5–19.5
Nickel (Ni)	8.0–10.5
Nitrogen (N)	0.10 max
Iron (Fe)	Остальное

One caution before you copy this into a specification. A large number of datasheets in circulation still list Type 304 as carbon 0.08 max with chromium 18.0–20.0. Those are legacy figures carried over from earlier editions and from the AISI designation, and they are not identical to the harmonised limits shown above. When a mill certificate and a customer specification disagree on the carbon ceiling, the argument is almost always an edition mismatch rather than a non-conforming heat. Name the edition on the purchase order and the problem disappears.

Mechanical minima, and why 304L is on the same page

Property	304 (S30400)	304L (S30403)
Tensile strength, min	515 MPa (75 ksi)	485 MPa (70 ksi)
Yield strength (0.2% offset), min	205 MPa (30 ksi)	170 MPa (25 ksi)
Elongation in 50 mm, min	40%	40%
Hardness, max	201 HBW / 92 HRB	201 HBW / 92 HRB
Carbon, max	0.07	0.030

The trade-off is visible in one line of that table. Dropping carbon to 0.030 max suppresses chromium carbide precipitation at grain boundaries during welding, which is what causes sensitisation and subsequent intergranular corrosion in the heat-affected zone. You pay for it with roughly 30 MPa of tensile and 35 MPa of yield.

For welded pressure-containing equipment that will see corrosive service, that trade is usually worth making, which is why 304L appears so often in petrochemical specifications where the drawing says “304 or 304L.” For thin sheet where the weld cools fast and the section is light, standard 304 is frequently acceptable.

A practical middle route exists. Many mills now produce heats that satisfy the 304L carbon ceiling while still meeting the 304 mechanical minima, and certify the material to both. Dual-certified 304/304L stock lets a fabricator draw one material for welded and unwelded parts on the same job. If you are stocking rather than buying to a single order, ask whether dual certification is available before splitting your inventory into two grades.

For pressure vessels, the letters in front of the number decide everything

This is the point that separates a compliant order from an expensive one.

ASME Boiler and Pressure Vessel Code, Section II Part A, contains ferrous material specifications designated with SA numbers. ASME describes these as identical with or similar to specifications published by ASTM and other recognised bodies. The stainless flat-product entry is SA-240.

If a vessel is being built to the ASME Code and stamped, the material must be supplied to SA-240 and certified accordingly. Material certified only to ASTM A240 is not automatically acceptable to the Authorised Inspector, even when the chemistry and mechanical results are identical, because Code acceptance runs on the SA designation and on the associated documentation requirements. Confirming this at enquiry stage costs one email. Discovering it at the inspection stage costs a re-order and the schedule.

Three follow-on points that belong in the same conversation:

1. If the vessel is being built to a European code instead, the reference is normally the EN system, where the equivalent austenitic grade appears as 1.4301 for 304 and 1.4307 for 304L. A CEN-referenced specification and an ASTM-referenced specification are not interchangeable on paper even when the metal is comparable.
2. Impact testing, additional NDT, and supplementary requirements are usually invoked by the vessel code, not by A240 itself. Those need to be stated on the order as supplementary requirements or the mill will not perform them.
3. Positive material identification at receiving is common practice in petrochemical work. It verifies alloy content, not grade conformance, so it does not replace the certificate.

Product form: sheet, plate and strip are defined by dimensions

A240 covers three product forms. The distinction is dimensional, and it matters because tolerance tables and often pricing follow the form rather than the alloy.

Форма	Толщина	Ширина	Typical supply
Лист	Under 4.76 mm (3/16 in)	600 mm and over	Coil or cut sheet, cold rolled
Лента	Under 4.76 mm	Under 600 mm	Coil, slit
Лист	4.76 mm and over	250 mm and over	Cut plate, hot rolled and annealed

The practical consequence: a buyer asking for “304 sheet, 8 mm” is asking for plate, and will get plate tolerances, plate surface condition and plate pricing. That is not a supplier being difficult. Hot rolled annealed plate arrives with a No.1 surface, which is dull and slightly scaled compared with the 2B finish a cold rolled sheet buyer expects, and no amount of ordering will make an 8 mm hot rolled product look like 2B unless it is separately polished.

Surface finishes and where each one is actually appropriate

Finish designations for flat-rolled stainless are defined in A480. The five most commonly stocked:

Отделка	Production route	Appearance	Where it belongs
2B	Cold rolled, annealed, pickled, light skin pass	Smooth, slightly reflective grey	The default for fabrication, tanks, process equipment, anything to be welded or later polished
BA (светлый отжиг)	Cold rolled, bright annealed in controlled atmosphere	Bright, reflective, no pickling scale	Where reflectivity is needed without polishing cost; appliance panels, some hygienic equipment
No.4	Mechanically abraded, uniform short grain	Brushed, directional matte	Architectural panels, kitchen and food equipment, wall cladding
HL (Hairline)	Mechanically abraded, long continuous grain	Fine continuous linear brush	Lift interiors, façade panels, decorative joinery
Mirror (No.8)	Progressive polishing and buffing	Highly reflective	Decorative and reflective applications only

A misconception worth killing here: surface finish and corrosion performance are not the same lever. A smoother finish reduces the number of crevices where deposits can sit, which helps in hygienic service, but it does not change the alloy’s resistance in a chloride environment. Ordering Mirror finish for a chemical storage tank interior adds significant cost and buys nothing structural. If the concern is chloride pitting, the answer is a molybdenum-bearing grade such as 316L, not a shinier 304.

The reverse case matters too. Material that will be welded and then polished should generally be bought as 2B. Buying a polished finish and then welding through it means paying twice for a surface you destroy.

Luyuan Steel stainless sheet: published parameters

• Продукция:Лист из нержавеющей стали
• Published grades:304 / 316L
• Published thickness range:3–12 mm
• Published surface finishes:2B / BA / No.4 / HL / Mirror
• Related published stainless products:Рулонная нержавеющая сталь (0.11–2.50 mm), Stainless Steel Pipe, Пруток из нержавеющей стали (304 / 304L / 316 / 316L / 321)
• Processing available:cutting, bending, punching, polishing, welding, moulding, depending on product
• Documentation:English Mill Test Certificate supplied with shipment, with batch traceability from furnace number through to shipment
• Inspection:100% pre-shipment inspection; SGS, Bureau Veritas, Intertek or buyer-appointed third-party inspection accepted

Two honest notes about how that range maps onto this article.

The published 0.3–12 mm band spans both the sheet and the plate side of the dimensional boundary above. The thinner part of it covers linings, tank cladding, ducting, heat exchanger components and light fabricated equipment. Heavy vessel shell plate for high-pressure service commonly runs well above 12 mm, so a shell-plate enquiry needs to be confirmed for availability rather than assumed from this listing.

More importantly: A240 or SA-240 conformance is not stated in Luyuan’s published product data, and no SKU-level certificate number is publicly disclosed. Nothing in this article should be read as a claim that stocked material is certified to A240, SA-240 or any pressure-vessel code. If your application requires that certification, state it as a requirement on the enquiry, ask which specification and edition the material will be certified to, and require that the certificate name it. Any supplier, including this one, should be asked the same question in the same words.

Specifying it so the certificate matches the order

1. Name the material specification and edition: ASTM A240/A240M, or ASME SA-240 if the part is Code work.
2. Name the grade and UNS number: Type 304, UNS S30400. Add “or dual-certified 304/304L” if that suits your stock plan.
3. State the product form you expect: sheet, strip or plate. Do not let the thickness contradict the word.
4. Give thickness in millimetres with the tolerance standard: to ASTM A480/A480M, or a stated tighter tolerance.
5. State width, length, and whether mill edge or trimmed edge.
6. State the finish designation, not a description: 2B, BA, No.4, HL, No.8.
7. State the condition: annealed and pickled, or bright annealed.
8. State any supplementary requirements the vessel code imposes, including intergranular corrosion testing per ASTM A262 if the specification calls for it.
9. Require an English Mill Test Certificate showing heat number, full chemical analysis, tensile, yield, elongation, hardness, and the specification and edition certified to.
10. State Incoterms, destination and packing. Stainless sheet marks easily, so specify interleaving or PVC film if the surface is a finished face.

Item 6 is the one that generates the most rework. “Brushed finish” is not a specification. No.4 and HL are both brushed and they do not look alike side by side on the same wall.

Часто задаваемые вопросы

В: ASTM A240 304 — это то же самое, что AISI 304?

О: Это близкие по составу материалы, но документы разного рода. AISI 304 — обозначение марки из системы нумерации, которая больше не ведётся для новых марок. ASTM A240 — действующая спецификация на продукцию с определёнными пределами по химическому составу, минимальными механическими свойствами и требованиями к испытаниям; пределы для Type 304 в ней не идентичны устаревшим значениям AISI, которые до сих пор приводятся во многих паспортах. Покупайте по A240 и указывайте редакцию.

В: Можно ли применять материал ASTM A240 для сосуда по нормам ASME?

О: Не как замену, которую вы решаете самостоятельно. Конструкция по Code требует материала по спецификации SA — в данном случае SA-240 — с документацией, предусмотренной Code. Если сосуд будет клеймиться, запросите сертификацию SA-240 уже на этапе запроса.

В: Что такое ASTM A959 и почему он встречается в запросах нефтехимической отрасли?

A: It is a guide to harmonised standard grade compositions for wrought stainless steels, useful for cross-referencing grade designations between national systems. It is not a product specification, so material cannot be ordered or certified “to A959.” Convert the enquiry to A240 or SA-240 and keep A959 as a cross-reference.

В: Что указывать для сварного резервуара — 304 или 304L?

О: Если в резервуаре будет агрессивная среда, а сварные швы не пройдут последующий аустенизирующий отжиг, безопаснее указать 304L: пониженное содержание углерода ограничивает сенсибилизацию в зоне термического влияния. Взамен вы теряете около 30 МПа минимального предела прочности. Материал с двойной сертификацией 304/304L удовлетворяет обоим требованиям в одной плавке — стоит о нём спросить.

В: При какой толщине материал считается толстым листом, а не тонким?

О: Условная граница — 4,76 мм (3/16 дюйма): тоньше — тонкий лист, от этой толщины и больше — толстый лист. От этого зависит, какая таблица допусков применяется, какое состояние поверхности вы получите и нередко как формируется цена. Указывайте нужную форму поставки по названию.

В: Улучшает ли зеркальная отделка коррозионную стойкость?

О: Существенно — нет. На более гладкой поверхности откладывается меньше загрязнений, что полезно в гигиенических областях, где важна возможность очистки, но поведение сплава в хлоридных средах от этого не меняется. Если риск — питтинг, переходите на молибденсодержащую марку, а не на более блестящую отделку.

В: Что должен содержать сертификат испытаний завода на лист A240 304?

О: Номер плавки, полный химический анализ по указанной марке, временное сопротивление, предел текучести, относительное удлинение, твёрдость, состояние термообработки, а также спецификацию и редакцию, по которой выдан сертификат. Если в качестве дополнительного требования проводились испытания на межкристаллитную коррозию, должны быть указаны метод ASTM A262 и результат. Проверьте, что строка со спецификацией в сертификате слово в слово совпадает со строкой в вашем заказе.